Redesigning a Stalk Chopper Mechanism for Reducing Cutting Energy and Optimizing Its Bite Length

Document Type : Original Research

Authors

1 Department of Mechanical Engineering of Bio-systems, Agriculture and Natural Resources Campus, Razi University, Kermanshah, Iran

2 Department of Mechanical Engineering of Bio-systems, Karaj Agriculture and Natural Resources Campus, Tehran University, Karaj, Iran

Abstract

Considering the increasing population of the world and the lack of human food sources, it is very important to pay more attention to fodder plants that can indirectly supply human food. By using choppers, a large amount of fodder can be transported and prepared for anaerobic fermentation of fodder.  In this research, a control mechanism has been proposed to change the angle of the knives on the cutting drum with a tangent plane on the circumference of the drum in order to change the distance between the knives and the fixed knife and change the length of the pieces. The mechanism was analyzed in SAM software, and then the three-dimensional model of different blade angle states was designed and analyzed in CATIA V5 R21 software. According to the obtained data, although the Von Mises stresses occur at the minimum angle of 22 degrees and the maximum Von Mises stress occurs at an angle of 16.5 degrees, there is no significant difference in the amount of stresses. Therefore, this mechanism can be recommended for all the mentioned situations (angles). For 1600rpm rotational speed and 6083 N/m line force density the occurred Von Mises stress in 22 degree angle is lower than zero degree angle.

Keywords


Aygun, I and Cakir, E (2014). Development and determination of the field performance of stalk choppers equipped with different blade configurations. Bulgarian Journal of Agricultural Science, 20, 1268-1271.
Azadbakht, M, Taghizadeh, A, Hashemi, A and Janzadeh, G (2013). Analysis of Stresses on Straw Walker Crankshaft of John Deere 955 Combine Harvester. Universal Journal of Agricultural Research, 1, 9-16.
Behrozilar, M and Aqbaei, L (2019). Tractor and agricultural machinery management, University of Tehran Printing and Publishing Institute.
Borotov, A. (2020). Cutting length the fodders of green stalks by drum chopper. IOP Conference Series: Materials Science and Engineering. IOP Publishing, 012160.
Guo, Z, Zhou, Z, Zhang, Y and Li, Z (2009). Bionic optimization research of soil cultivating component design. Science in China Series E: Technological Sciences, 52, 955-965.
Meriam, J and Kraige, L (2011). Engineering Mechanics: Statics: Statics, Wiley Global Education.
Rains, G and Cundiff, J (1993). Design and field testing of whole-stalk sweet sorghum harvester. Applied Engineering in Agriculture, 9, 15-20.
Srivastava, AK, Goering, CE, Rohrbach, RP and Buckmaster, DR (1993). Engineering principles of agricultural machines, American society of agricultural engineers Saint Joseph.
Suleimanzadeh, J and Heydarbeigi, K (2018). Simulation and mechanical analysis of the cutting blade of fodder chopper using finite element method (FEM). 11th National Congress of Biosystem Mechanical Engineering and Mechanization of Iran.
Tarighi, J, Mohtasebi, SS and Alimardani, R (2011). Static and dynamic analysis of front axle housing of tractor using finite element methods. Australian journal of Agricultural Engineering, 2, 45-49.
Tian, K, Li, X, Zhang, B, Chen, Q, Shen, C and Huang, J (2017). Design and test research on cutting blade of corn harvester based on bionic principle. Applied bionics and biomechanics, 2017.
Xie, L, Wang, J, Cheng, S, Zeng, B and Yang, Z (2018). Optimisation and finite element simulation of the chopping process for chopper sugarcane harvesting. Biosystems Engineering, 175, 16-26.
Yilmaz, D, Hamamci, E, Salik, D and Ahiskali, Y (2011). Structural analysis of agricultural machinery: a case study for a transport chassis of a spraying machine. Tarım Makinaları Bilimi Dergisi, 7, 405-409